Hauler-racks V11SEV-1 Instrukcja Użytkownika Pobierz pdf

ASSEMBLY INSTRUCTIONS FOR

V10SE & V11SE ‘E’ MOUNT RACKS

P/N V10SEV-1 / V11SEV-1

V10SEV-1 shown above

PARTS

(1) RAIL DRIVER’S (LEFT) SIDE ASSEMBLY

(1) RAIL PASSENGER’S (RIGHT) SIDE ASSEMBLY

(1) FRONT RECTANGLULAR CROSSBAR

(1) REAR CROSSBAR

(2) MIDDLE CROSSBAR ASSEMBLIES WITH ‘H’ BRACKETS

(6) CURVED ARMS

(6) E-MOUNTS

Package Contents:

HARDWARE KIT

(6) CLIPS

(6) CLIP END CAPS

(8) 3/8”-16 x 3” CARRAIGE BOLTS

(16) 3/8”-16 x 2” CARRAIGE BOLTS

(4) 3/8”-16 x 1-3/4” CARRAIGE BOLTS

(4) 3/8”-16 x 1-1/2” HEX BOLTS

(32) 3/8”-16 NUTS

(32) 3/8” SPLIT LOCK WASHERS

(12) 5/16”-18 x 1” CARRIAGE BOLTS

(12) 5/16”-18 NUTS

(12) 5/16” SPLIT LOCK WASHERS

(6) ¼”-20 X 3/4” PHILLPS SCREWS

(6) ¼”-20 X 1-1/2” PHILLPS SCREWS

(6) 1/4” -20 NUTS

(12) ¼” SPLIT LOCK WASHERS

Before you begin:

Remove all components from the shipping carton.

The rack should be assembled on a padded surface such as carpet to prevent scratching of aluminum surfaces. Remove bands

securing components together.

Read the instructions thoroughly to familiarize yourself with the assembly sequence.

Note that you DO NOT tighten any nuts and bolts until the completed rack is installed on the vehicle unless specified. This allows for

minor adjustments to the rack during the installation process.

Gather the following tools used to assemble and install the rack.

9/16” Socket or open end wrench

1/2” Socket or open end wrench

7/16” Socket or open end wrench

Phillips screwdriver

HAULER RACKS, INC. Toll Free: 1-800-843-5445

7109 31

Avenue North Phone: 763-546-5620

Minneapolis, MN 55427-2848 Fax: 763-546-0933

Page 1 of 10 WWW.HAULERRACKS.COM

1 2 3 4 5 6 7 8 9 10

Podsumowanie treści

Strona 1 - P/N V10SEV-1 / V11SEV-1

ASSEMBLY INSTRUCTIONS FOR V10SE & V11SE ‘E’ MOUNT RACKS P/N V10SEV-1 / V11SEV-1 V10SEV-1 shown above PARTS (1) RAIL DRIVER’S (LEFT) SIDE ASS

Strona 2

HAULER RACKS, INC.

Strona 3

HAULER RACKS, INC.

Strona 4

1. (Continued) Connect front and rear sections Note the orientation of the other carriage bolts on rail assemblies. For the top round tube, us

Strona 5

HAULER RACKS, INC.

Strona 6

HAULER RACKS, INC.

Strona 7

4. (Continued) Crossbar assembly Remove the (4) 3/8” split lock washers and (4) 3/8”-16 nuts from the middle front and middle rear crossbar assemb

Strona 8

6. Place middle crossbars assemblies. The middle crossbar assemblies are the ribbed rectangle extrusions with a slotted bottom and ‘H’ brackets att

Strona 9

7. Install rear crossbar. The rear crossbar is the rectangular extrusion with a ribbed bottom and square bolt holes in each end. Using (4) 3/

Strona 10

8. Mounting to Van Place the rack on the van (an assistant is highly recommended) and position to the desired location. Adjust the E-mounts to th

Powiązane modele: V10SEV-1

Komentarze do niniejszej Instrukcji

Brak uwag

Hauler-racks V11SEV-1 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Do samochodu Hauler-racks V11SEV-1. Hauler Racks V11SEV-1 User Manual Instrukcja obsługi

Podsumowanie treści

Powiązane modele: V10SEV-1

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Do samochodu Hauler-racks V11SEV-1